Dein off-grid Energie Projekt...

...für das Gartenhaus, den Camper oder einfach als unabhängige Energielösung für unterwegs.

Wie erstelle ich mein eigenes, unabhängiges Stromsystem – für das Gartenhaus, den Camper oder einfach als unabhängige Energielösung für unterwegs zusammen? Im folgenden Bericht stellen wir Euch das Zusammenspiel der verschiedenen Komponenten vom Solarpanel bis zum Anschluss eines 230V Wechselrichters vor. 

Mit nur wenigen Komponenten und Handgriffen – (fast) alles mit Strom versorgen – unabhängig, sicher und erneuerbar.

Schritt 1:

Berechnung des benötigten Stromspeichers.

Was will ich mit meinem unabhängigen Stromspeicher betreiben können? Diese Frage bringt Euch zum Resultat, wie lange die geplante Anwendung oder der Verbraucher ohne zusätzliche Ladung der Batterie funktionieren kann.

Machen wir ein kleines Beispiel: Ihr wollt Eure Stereoanlage mit 200 Watt Leistungsaufnahme betreiben können. Bei unseren LiFePO4 Batterien sind immer die Wattstunden ausgewiesen, die sogenannte Energiemenge. Haben wir also eine Batterie mit 12.8V 100Ah = 1280 Wh (Wattstunden), dividiert Ihr die 200 W durch die 1280 Wh und ihr erhaltet als Resultat, wie lange die Stereoanlage mit der Batterie betrieben werden kann. In diesem Falle wären es 1280 Wh/200 W = 6.4 Stunden.
Die Stereoanlage würde also 6.4 Stunden autark ohne weitere Stromversorgung funktionieren.

Hinweis: Es handelt sich hierbei um eine vereinfachte Berechnung. Faktoren wie Wirkungsgrad, Leistungsverlust und Umgebungstemperaturen sind hier nicht kalkuliert. Diese können das Berechnungsresultat leicht verändern. Bei Fragen stehen wir Euch natürlich gerne zur Verfügung.

Step 2:

How big should the solar panel be?

The selection of the right solar panel depends on the one hand on the possible area for the equipment (roof, car roof), but is also an interaction of the selected battery storage. The question here is how quickly the battery should be able to be recharged by the solar power. The technical data of the solar panel are decisive here. For this we need the imp value (current at maximum power) of the solar panel. As an example: Our 150W flexible solar panel has an imp of 9.38A. Now we take the 12.8V 100Ah 1280Wh LiFePO4 battery again. To be able to charge our battery with a solar panel from 0-100%, we need about 10 hours of optimal sunlight. (Capacity 100Ah divided by maximum charging current 9.38A) Our solar panels are available as rigid versions with an aluminium frame, as flexible versions for curved surfaces and low installation heights or as foldable panels for mobile use.

Note: This is a simplified calculation. Factors such as angle of irradiation to the sun and power loss due to heat are not calculated here. These can change the calculation result. If you have any questions, please do not hesitate to contact us.

Step 3:

The heart between solar and battery! 

The solar charge controller.

To be able to charge the battery properly, you still need a solar charge controller. The solar charge controller takes the voltage (V) and current (A) of the solar panel and converts it into the correct charging power for the battery. Each battery technology has its own charging method.

The battery technology used is set on the solar charge controller and the rest is done by the device. The solar charge controllers are each designed with a maximum output current.

Example: 30A. This means that 3 x 150W Swaytronic solar panels can be flexibly connected to a 30A solar charge controller. We at Swaytronic only use solar charge controllers with MPPT technology (Maximum Power Point Tracking). These are characterised by a maximum power yield between the solar panel and the battery.

Note: If you have any questions or would like to choose the right charge controller, we are of course at your disposal.

Step 4:

How can I use 230V devices? 

The inverter.

The self-sufficient system is basically complete after step 3. The battery now has between 12-48V DC (direct current), depending on the circuit. How can I now operate 230V AC (alternating current) appliances?

This is where the inverter comes in. The inverter/converter regulates the DC voltage up to AC voltage. Then appliances with AC230V can be operated directly, e.g. a coffee machine.

The differences between the inverters lie in the output power (watts). The higher the power of the consumer, the higher the output power of the inverter should be. 

Note: If you have any questions or would like to choose the right inverter, please do not hesitate to contact us

Swaytronic project request

Are you looking for a partner for design & engineering of a special configuration? 
Or would you like to request a complete solution in the field of mobile energy?
We offer you a "full service" from the drawing board to the certification of your project / product.


The following questions will help us to better understand your project and ensure the best possible start to your project!

Contact
Directions
Calculators
b
c